1*JVS to USB Controller Adapter Based On MP07- IONA-US For TTX2 3/Sega Naomi 1 2

Description: You may also like1 PC to 2 Monitor 2 Port VGA SVGA Video LCD Splitter Box Adapter w/ Power Cable14.44 USDLower Duct Hose for Shark Rocket True Pet Slim Vacuum HV300 HV322 320 380 380UK4.99 USD3.69 USDFor JR SPECTRUM DSM-X DSM2 Transmitter Two Modes S603 Receiver 6CH 2.4GHz PPM24.15 USD100pcs Multi Sizes Watch Crown Pusher Spring Assortment for Watch Repair Parts16.05 USDMount Bracket Back Board Plate Kit For AMD Socket AM4 CPU Fan Cooler Heatsink5.99 USD3.69 USDReplacement Controller Silicon Rubber Conductive Pad Buttons For Sony PS43.99 USD3.69 USD 1*JVS to USB Controller Adapter Based On MP07- IONA-US For TTX2 3/Sega Naomi 1 2 Product Description Features:Compatible with for Xbox 360 / for Xbox One series/for PS4/for PS3/for Switch pro controllers.Custom Button Layout, map at most 12 physical buttons to arbitrary logical buttons for JVS.Rapid-fire,enable rapid-fire mode per each physical button.Persistent Configurations, store and restore at most 10 configuration sets of button layout, rapid-fire settings, and it’s speedFirmware Updates,For bug fixes, or to improve compatibility, firmware updates are available.Twin stick mode, When a for PS4 controller is connected to the 1P USB port, pushing PS button switch operation mode between the normal mode and the twin stick mode.Mahjong mode,When a USB keyboard supporting boot mode, though almost all keyboards will support, is connected, IONA switches to mahjong mode.Settings:Transit operation modesOn boot, IONA runs in the normal mode. Operation modes are transited by pressing TEST and SERVICE buttons on the IONA board.① Normal mode (LED - blink or on, depending on JVS bus state)Works as a JVS I/O controllers with chosen settings.② Layout config mode (LED - fast blink)On pushing TEST and SERVICE together, it enters the layout config mode. you need to press both for at least 0.5 and at most 5 seconds together. You don’t need to push them exactly together, e.g. keeping TEST down and clicking SERVICE will work.In the button layout mode, you will choose physical buttons in the following order, coin, start, button1 to 10. If you push multiple buttons together, you can assign multiple physical buttons into one button. You don’t need to push them at the eaxctly timing as well.When you press a button, IONA starts recording all pressed buttons until all buttons are released, then assign them all to the target button. You continue this sequence until all 12 buttons are mapped. If you leave this mode before settings all, remaining buttons are remained to have no assignment. If you configure no button, exceptionally IONA doesn’t update layout at all and move to the next mode.③ Rapid-fire config mode (LED - blink)You can press multiple physical buttons for which rapid-fire is enabled. Similarly, timing should not be exact. You can try multiple time until existing from this mode.④ Speed config mode (LED - slow blink)You can choose rapid-fire speed by button 1 - 6. Button 1 - 6 does not mean the physical buttons, but buttons mapped in the custom layout. Each button 1 - 6 are mapped to 30/20/15/12/10/8.5 fps. You can try any time until exiting from the mode. If you push multiple buttons, faster speed is taken. If release timing differs, the latter one is taken.Chosen settings above will be stored persistently.⑤ Factory reset (LED - flash)You can reset all settings and restore default settings by pressing TEST and SERVICE together outside the normal mode. LED flashes, then go back to the normal mode automatically.⑥ Call store config (LED - off)You can enter the mode to call stored config by pushing SERVICE button outside the normal mode. Pressing button 1 - 10 in the custom layout recall the configuration set 1 - 10. Initial set for the factory setting is 1. You can recall another config again until exiting the mode by pressing SERVICE again. It returns to the normal mode if the firmware is older than 1.40 by pressing SERVICE. Otherwise, ver 1.40 and later, pressing TEST moves to the analog layout config mode.⑦ Analog layout config mode (LED - fast blink)You can choose 6 inputs for analog signal reports. Analog input values are remembered as base values when you enter this mode. You can move an analog stick or a trigger that are recognized as analog inputs. You may want to move it right, down, or pushed for normal polarity. If you want to revese it, you can move it toward the opposite side. Once you stop moving the stick or the trigger and make it return to the original position, the input was recorded. You need to repeat the same steps for analog input 1 to 6, 6 times. You can quit this mode by pressing TEST, and following assignments are just skipped and previous settings are used.⑧ Options config mode (LED - blink)You can quit the settings mode by pressing TEST, but options will be set via P1 buttons on quitting the mode as below. The button number is logical one based on.USE Guide:1. Connect USB Type C port for power supply. It doesn’t need data connection as it’s just expected to suupply 5V power for IONA.USB charger will be available. Of course, PC USB port can support the required power.PC-based JVS system board could have a port for this use, e.g. exA-Arcadia has hidden USB ports.But if you want to use a device that requires much power, supplying via USB Bus from PC may not be enough and IONA gets to be unstable.2. Connect JVS port to the JVS system board. You can use a general USB cable.3. Connect USB gamepads at any timePackage include:1* JVS to USB Adapter(Does not include any cables or chargers) Shipping Returns Contact Us Payment Shipping 1. Items sent from US warehouse.2.Receiving time = Processing time + Shipping time3. Processing Time: Around 1-2 business Days4. Shipping Time: 3-5 business dayit may have a little delay during some holiday (such as Christmas),any problem ,please feel free to contact Returns 1.30 days warranty from the purchased date. Please contact us via email before returning the defective item.2.Our warranty does not extended to any product that are physically damaged or that are not under normal operating conditions as result of misuse or improper installation on the buyer/users part.3.Return items should include the original packaging and all accessories. buyers MUST contact us for the returning address.4.In all cases, buyers pay shipping fees at their own cost to return products for exchange or refund. We will be responsible for the postage of replacements. Refund will be made upon receipt of the returned item. Contact Us Pls contact us if you have any problems,we will try our best to solve for you Payment We accept all verified payment from eBay. Copyright © 2022 Tongtool

Price: 38.99 USD

Location: Walnut

End Time: 2024-08-05T19:35:47.000Z

Shipping Cost: 0 USD